@article { author = {حسنلو, مجتبی and باقری, احمد}, title = {Intelligent Control Smart Timoshenko Beam by Using MOPSO-PID Controller Based on Optimal Location PZT Patch Actuator Approach}, journal = {Iranian Journal of Mechanical Engineering Transactions of ISME}, volume = {20}, number = {3}, pages = {6-28}, year = {2018}, publisher = {ISME}, issn = {2538-4775}, eissn = {}, doi = {}, abstract = {The significance of vibration omission in the engineering structures has led the striking vastness for the applied designing science. The role of vibration omission in materials with emphases on energy-saving and cost reduction is such a topic that has been analyzed and discussed as a challenge in the mechanical engineering. Here, a steel structure with a certain number of piezoelectric pieces with specific dimensions is considered. The aim is to omit vibrations or reduce the vibration range at the minimum time. In this paper, the placement of piezoelectric is carried out in order better to accelerate the suppression of vibration amplitude using the MOPSO, an optimization algorithm. Piezoelectric elements are installed as sensors and actuators on the top and bottom of structures. An early rise is applied to the structure and thus it begins vibration and the amplitude of these vibrations is suppressed by the piezo actuators. Piezoelectric sensors sense the structure’s vibration motion and control operations are done based on it, and finally to suppress, a control signal is sent to the actuators. The result of this motion is the structural vibration suppression. In this thesis, the studied structure is Timoshenko beam.}, keywords = {Piezoelectric,Vibration Suppression,structure,MOPSO Algorithm,PID Controller}, title_fa = {کنترل هوشمند تیرتیموشنکو با استفاده از الگوریتم بهینه‌سازی چندهدفه ازدحام ذرات و کنترلرPID مطابق با نگرش جایابی بهینه وصله‌های محرک پیزوالکتریک}, abstract_fa = {تیر با شرط مرزی یکسرگیردار به بررسی ارتعاشی عرضی تیر تحت اثر بارخارجی میگیرد. این بار خارجی بصورت پالس، ایمپالس، پله و متناوب سینوسی میباشد. برای کنترل سازه از کنترلر PID استفاده شده است. کنترلر 3 ضریب مجهول در ماتریسهای Kp، Kd، Ki قرار دارند که با استفاده از الگوریتم بهینه سازی ازدحام ذرات چندهدفه یا MOPSO، ضرایب مجهول در اثر جستجوی این الگوریتم در طول تیر محاسبه شده و به تعیین نقطه یا نقاطی بهینه از تیر جهت قرارگیری حسگر و عملگر پیزوالکتریک در بالا و پایین تیر برای میرا نمودن سازه در کمترین زمان ممکن منجر میشود.}, keywords_fa = {پیزوالکتریک,میرایی ارتعاشی,سازه,الگوریتم بهینه‌سازی MOPSO,کنترلرPID}, url = {https://jmep.isme.ir/article_33766.html}, eprint = {https://jmep.isme.ir/article_33766_0e1a6171f44828d5c028273f1a095a97.pdf} } @article { author = {Shirzad, Masoud and فتحی, علیرضا and rabiee, sayad mahmood}, title = {Fabrication and Analysis of a 3D truss Pattern Scaffold made by 3D printing Method}, journal = {Iranian Journal of Mechanical Engineering Transactions of ISME}, volume = {20}, number = {3}, pages = {30-40}, year = {2018}, publisher = {ISME}, issn = {2538-4775}, eissn = {}, doi = {}, abstract = {In this paper, a new pattern was offered for the fabrication of tissue engineering scaffolds by the 3D printing method. A photocurable resin, micro mirror and UV source were employed for the fabrication of scaffolds. Final patterns have a simple form and a gradient form that the mechanical behavior of each model was investigated under mechanical testing. For the investigation of precise mechanical behavior of porous samples, non-porous samples were investigated under mechanical testing and an empirical equation were used for the checking influence of base material properties on the behavior of porous samples. The results indicate that the gradient model, unlike the simple model has multiple elastic regions under the large displacement because of their special design. This behavior is very important for the scaffolds that were implanted in hard tissue and tolerate a high pressure Using this type of layering beside the biological advantage of gradient model can improve the efficiency of scaffolds.}, keywords = {Scaffold,3D printing,Mechanical properties,3D truss}, title_fa = {ساخت وتحلیل داربست ساخته شده به وسیله الگوی خرپای سه بعدی و روش پرینت سه بعدی}, abstract_fa = {در این مقاله الگوی نوینی برای ساخت داربست‌های مهندسی بافت، با استفاده از روش پرینت سه‌بعدی ارائه شده است. جهت ساخت داربست‌ها از رزین آکریلاتی حساس به نور استفاده شده است. نمونه‌های نهایی دارای دو ساختار ساده و گرادیانی می‌باشند که رفتار مکانیکی آن‌ها مورد بررسی قرار گرفته است. خواص مکانیکی نمونه‌ها با استفاده از تست فشار تک‌محوره و معادله تجربی مورد بررسی شد. نتایج نشان می‌دهد که تحت تغییر شکل‌های بزرگ در نمونه‌ گرادیانی برخلاف نمونه ساده نواحی الاستیک متعددی بوجود می‌آید. استفاده از این نوع لایه‌بندی در کنار مزیت زیستی نمونه گرادیانی می‌تواند کارایی داربست-ها را بهبود بخشد.}, keywords_fa = {داربست,پرینت سه بعدی,خواص مکانیکی,خرپا سه بعدی}, url = {https://jmep.isme.ir/article_33767.html}, eprint = {https://jmep.isme.ir/article_33767_c1d6fabfcbfec778a8da88efd010a7c6.pdf} } @article { author = {Bajelan, Mahdi and Mohamadzadeh, Parviz and Fakoor, Mahdi}, title = {Design for reliability: optimization of critical structures using cross-entropy reliability analysis}, journal = {Iranian Journal of Mechanical Engineering Transactions of ISME}, volume = {20}, number = {3}, pages = {41-58}, year = {2018}, publisher = {ISME}, issn = {2538-4775}, eissn = {}, doi = {}, abstract = {This article presents an efficient reliability-based optimization method for critical structural design, in which, the probability of failure (Pf) should remain in a small bound. Critical structures should be designed to be optimal and reliable. Despite significant progress in reliability and optimization techniques, their interaction, which is considered in reliability-based optimization (RBDO), is faced with several challenges, especially in reliability analysis of critical constraints (constraints with Pf less than 10-5). To address this issue, in this paper the cross-entropy method is intended for reliability analysis and is combined with Genetic Algorithm in a double-loop framework to implement RBDO. The cross-entropy method is based on Monte Carlo simulation, except that the variance of sampling is reduced, which leads to a faster and more accurate reliability analysis method. The proposed RBDO method is demonstrated on two structural design. The obtained results show a high capability in reliability-based optimization of critical structures. In addition, using the proposed method, in comparison with traditional safety factor method, provides a more substantial manner in reliability improvement.}, keywords = {Reliability-based Optimization,Critical Structure,Cross-Entropy,genetic algorithm}, title_fa = {طراحی برای قابلیت اطمینان: بهینه‌سازی سازه‌های بحرانی با استفاده از تحلیل فاصله بی‌نظمی}, abstract_fa = {در این مقاله، یک روشِ طراحی برای قابلیت‌اطمینانِ سازه‌های بحرانی ارائه شده است. روش فاصله بی-نظمی برای تحلیل قابلیت‌اطمینان ارائه شده و در چارچوب مناسبی با الگوریتم بهینه‌سازی تلفیق شده-است. علیرغم پیشرفت‌هایی که در زمینه قابلیت‌اطمینان و بهینه‌سازی صورت گرفته، هنوز در حوزه سازه-های بحرانی چالش‌های محاسباتی وجود دارد. در روش فاصله بی‌نظمی، واریانس نمونه‌های تصادفی لازم برای شبیه‌سازی مونت‌کارلو کاهش یافته و امکان تحلیل قابلیت‌اطمینان قیود بحرانی فراهم می‌شود. این روش بر روی دو نمونه طراحی سازه‌ای پیاده‌سازی شده و نتایج نشان می‌دهد که این روش در مقایسه با روش ضریب اطمینان، قابلیت‌اطمینان سازه را افزایش می‌دهد.}, keywords_fa = {بهینه‌سازی,قابلیت اطمینان,سازه بحرانی,فاصله بی‌نظمی,الگوریتم ژنتیک}, url = {https://jmep.isme.ir/article_33768.html}, eprint = {https://jmep.isme.ir/article_33768_ee8d41879a3e488f81004494cc9c6505.pdf} } @article { author = {خدایاری, علیرضا and Ghaffari, Ali and Amidpour, Majid and Mehrfarzam, Nasim}, title = {Design and Implementation of a Novel Algorithm for Optimal Building’s HVAC Systems Selection}, journal = {Iranian Journal of Mechanical Engineering Transactions of ISME}, volume = {20}, number = {3}, pages = {59-79}, year = {2019}, publisher = {ISME}, issn = {2538-4775}, eissn = {}, doi = {}, abstract = {HVAC systems are the biggest energy consumers in buildings. Hence, reducing energy consumption in this sector, while maintaining thermal comfort can be one of the vital policies in order to use saved energy in industrial section. This paper, analyzes and compares the effect of using different HVAC systems on energy consumption reduction and introduces a new algorithm for choosing an optimal HVAC system for a building. A five story residential building in Tehran has been considered as a case study to analyze proposed algorithm performance.Detailed building’s data and specifications like design plan, materials and HVAC system must be considered to increase the accuracy of the model. The model is validated based on energy consumption which does not need sensors installation. The model could be used to analyze building thermal behavior, energy consumption optimization and designing control systems with high accuracy. The comparison between the model and building’s real energy consumption shows less than one percent error which is acceptable.}, keywords = {HVAC System,Energy Simulation,Design Builder,Optimization,Energy Cost}, title_fa = {طراحی و ارائه الگوریتم انتخاب سیستم تهویه مطبوع بهینه ساختمان}, abstract_fa = {در این مقاله، تاثیر نوع سیستم تهویه مطبوع یک ساختمان بر کاهش میزان مصرف انرژی آن مورد بررسی قرار می گیرد و با استفاده از آن یک الگوریتم جدید برای انتخاب سیستم تهویه مطبوع بهینه ساختمان ارائه می شود. این الگوریتم قابلیت اجرا برای ساختمان های در حال ساخت و ساختمانهای ساخته شده را دارد. به منظور ارزیابی عملکرد روش پیشنهادی یک ساختمان مسکونی پنج طبقه در نظر گرفته شده و مراحل بر روی مدل این ساختمان شبیه سازی شده است. مقایسه بین مدل و ساختمان واقعی کم تر از یک درصد خطا نشان می دهد.}, keywords_fa = {سیستم تهویه مطبوع ساختمان,شبیه‌سازی انرژی,نرم‌افزار Design Builder,بهینه‌سازی,هزینه مصرف انرژی}, url = {https://jmep.isme.ir/article_34095.html}, eprint = {https://jmep.isme.ir/article_34095_eeb45497033a432302e8e0fc878463f2.pdf} } @article { author = {Bagheri, Rasul and Mahmoodi Monfared, Mojtaba and engilela, vali}, title = {Multiple cracks in a functionally graded electro-magneto- elastic rectangular plane}, journal = {Iranian Journal of Mechanical Engineering Transactions of ISME}, volume = {20}, number = {3}, pages = {80-108}, year = {2018}, publisher = {ISME}, issn = {2538-4775}, eissn = {}, doi = {}, abstract = {In this paper, the static problem of several cracks in a functionally graded piezoelectric–piezomagnetic (FGPP) rectangular plane subjected to concentrated anti-plane mechanical and in-plane electric and magnetic fields is described. The material properties are assumed to vary continuously according to exponential functions along the transverse of the FGPP rectangular plane. The dislocation method and integral transforms technique are applied to obtain a set of Cauchy singular integral equations. Thestress, electric and magnetic intensity factors for several cracks, are obtained by using the corresponding solution to these equations. The numerical examples of mode-III problem are presented to illustrate the interesting mechanical and electromagnetic coupling phenomena induced by multicrack interactions. Finally, the effects of material nonhomogeneity constant, the cracks length, position of point load and the cracks configuration upon the stress and electromagnetic intensity factors are investigated. The obtained conclusions seem useful for design of the magnetoelectroelastic structures and devices of high performance.}, keywords = {rectangular plane,Screw dislocation,Multiple cracks,field intensity factors}, title_fa = {تحلیل تنش در صفحه مستطیلی از جنس ماده الکترومگنتوالاستیک با رفتار تابعی حاوی چندین ترک}, abstract_fa = {در این مطالعه، تحلیل تنش در صفحه مستطیلی از جنس ماده الکترومگنتوالاستیک تابعی تضعیف شده توسط چندین ترک، تحت بار نقطه ای خارج صفحه ای مکانیکی و درون صفحه‌ای الکترومغناطیسی انجام شده است. در این مطالعه فرض شده که رفتار محیط الاستیک خطی است و سطوح ترکها هموار می‌باشد. از روش نابجایی، تبدیل فوریه محدود و روش جداسازی متغیرها برای بدست آوردن معادلات انتگرالی تکین از نوع کوشی استفاده شده است. برای صحت سنجی نتایج، تاثیرات ثوابت ماده، طول ترکها، محل اعمال بار نقطه ای و نحوه چیدمان ترکها بر روی ضرایب شدت میدانی، مثالهایی آورده شده است.}, keywords_fa = {چندین ترک,مواد هوشمند,مواد تابعی,-تکینگی کوشی,روش نابجایی}, url = {https://jmep.isme.ir/article_33769.html}, eprint = {https://jmep.isme.ir/article_33769_33518ad95f8eacf566ba39419dc0c780.pdf} } @article { author = {Rezaee, Mousa and vesal, rahim}, title = {Perturbation analysis of resonant and non-resonant excitations of a beam equipped with a nonlinear vibration absorber}, journal = {Iranian Journal of Mechanical Engineering Transactions of ISME}, volume = {20}, number = {3}, pages = {109-132}, year = {2018}, publisher = {ISME}, issn = {2538-4775}, eissn = {}, doi = {}, abstract = {In the current paper the impact of the presence of a damped nonlinear Dynamic Vibration Absorber on dynamic behavior of an Euler-Bernoulli clamped-free beam is investigated under resonant and non-resonant excitations. Accordingly, the governing equations of motion are derived and converted to the form of non-dimensional equations. Then, these equations are solved using the Multiple Scales Method after applying the Galerkin Method. It is assumed that the Dynamic Vibration Absorber damping is linear, and its stiffness is composed of two parts, a linear and a third order nonlinear one. Resonant and non-resonant cases have been taken into account for sinusoidal excitation. The influence of the Dynamic Vibration Absorber parameters on the system vibrational behavior is provided. Obtained results illustrate the possibility that under specific circumstances the nonlinear dynamic vibration absorber could have a better performance in suppressing the oscillation amplitude than a similar linear one in jumping phenomenon region. In addition, the results show that in non-resonant frequency regions, there is no major difference in system vibrational behavior in presence of linear damped, undamped and nonlinear vibration absorbers. Furthermore, in comparison with similar linear case, the nonlinearity of the absorber stiffness relocates the resonant frequencies, and makes changes in the non-resonant frequency region.}, keywords = {Nonlinear Dynamic Vibration Absorber,Resonant and Non-resonant Excitations,Multiple Scales Method,Jump Phenomenon}, title_fa = {تحلیل اغتشاشات تیر مجهز به جاذب دینامیکی غیرخطی تحت تحریک رزونانسی و غیررزونانسی}, abstract_fa = {تأثیر جاذب غیرخطی بر ارتعاشات پایای تیر یکسرگیردار تحت تحریک رزونانسی و غیررزونانسی بررسی شده‌است. پس از استخراج معادلات، بی‌بعدسازی و اعمال روش گالرکین، از روش مقیاس‌های چندگانه برای حل استفاده شده و تأثیر پارامترهای جاذب بر رفتار ارتعاشی سیستم مطالعه شده است. نتایج نشان می‌دهد در ناحیه پرش، تحت شرایط خاصی، امکان عملکرد بهتر جاذب غیرخطی در کاهش دامنه وجود دارد. همچنین، گرچه نتایج حاکی از عدم وجود تفاوت عمده‌ در رفتار ارتعاشی سیستم در حضور جاذب‌های خطی نامیرا، میرا و غیرخطی در تحریکات غیررزونانسی است ولی جاذب غیرخطی باعث جابجایی فرکانس‌های تشدید و تغییر بازه‌ی فرکانسی غیررزونانسی می‌شود.}, keywords_fa = {جاذب دینامیکی غیرخطی,تحریک رزونانسی و غیررزونانسی,روش مقیاس‌های چندگانه,پدیده پرش}, url = {https://jmep.isme.ir/article_33770.html}, eprint = {https://jmep.isme.ir/article_33770_21b22e0d19eb2f3a43c44cb60b12b93b.pdf} } @article { author = {Asadzadeh, Zahra and Eslami, Mohammad Reza}, title = {Nonlinear Axisymmetric, Thermally Induced Vibrations of a Functionally Graded Spherical Cap}, journal = {Iranian Journal of Mechanical Engineering Transactions of ISME}, volume = {20}, number = {3}, pages = {133-169}, year = {2018}, publisher = {ISME}, issn = {2538-4775}, eissn = {}, doi = {}, abstract = {In this study, thermally induced vibrations of a Functionally Graded Material (FGM) Spherical Cap discussed. Distribution of shell properties in the direction of thickness is calculated from volume fraction relationship. Dependency to temperature is expressed based on the Touloukian formula. Thermal loading on the shell is axisymmetric and the response of the shell have been considered axially symmetric. Ceramic rich surface of the shell is subjected to temperature rise, whereas the metal rich surface of the shell is kept at reference temperature or thermally insulated. Temporal evolution of temperature profile across the shell thickness is obtained through solution of one-dimensional heat conduction equation. This equation is originally nonlinear since temperature dependency of thermal conductivity is taken into account. The first-order shear theory and Von-Karman compatibility relations has been used for deriving the equation. Dynamics equations are derived using Hamilton's principle with the application of Ritz method has become a set of nonlinear time-dependent algebraic equations. Solving this set of equations is done with Newmark integral method help with numerical method Newton-Raphson. Solution of the transient one dimensional heat conduction equation with the arbitrary type of time-dependent boundary conditions is carried out employing the central finite difference method combined with the Crank–Nicolson time marching scheme. After validating the developed computer code, some parametric studies are accomplished to show the influences of various involved parameters. It is shown that temperature dependency, geometrical non-linearity, shell thickness, power law index, and the type of thermal loading, all affect the temporal evolution of plate characteristics.}, keywords = {Functionally graded material,Spherical Cap,Thermally Induced Vibration,Uncoupled Thermoelasticity}, title_fa = {تحلیل ارتعاشات غیرخطی متقارن‌محوری واداشته از حرارت در پوسته‌ی کروی ساخته‌شده از مواد هدفمند}, abstract_fa = {خواص پوسته از رابطۀ کسر حجمی به‌دست‌آمده، وابستگی حرارتی از رابطه تولوکیان لحاظ شده است. بارگذاری متقارن محوری میباشد. سطح سرامیکی در دمای ثابت و سطح دیگر در دمای پایینتر (یا عایق) است. توزیع دما از معادله گذرای غیرخطی غیرکوپل انتقال حرارت محاسبه میشود. از تئوری مرتبه اول پوسته و روابط کرنش-تغییرمکان فون-کارمن برای استخراج معادلات استفاده گردیده، معادلات دینامیکی از اصل همیلتون و روش ریتز بدست آمده و بوسیله روشهای نیومارک و نیوتن-رافسون حل شدهاست. معادله انتقال حرارت با روش تفاضل محدود و کرنک-نیکلسون حل شده است. اثر توزیع خواص، نوع بار حرارتی و هندسه در پاسخ بررسی شدهاست.}, keywords_fa = {مواد هدفمند,پوسته کروی,ارتعاشات واداشته از حرارت,ترموالاستیسیته غیرکوپل}, url = {https://jmep.isme.ir/article_33771.html}, eprint = {https://jmep.isme.ir/article_33771_db03e9a1af0cb36b0664ae17bb18dc62.pdf} } @article { author = {shariatmadar mortazavi zavareh, sayyed mojtaba and jafari gavzan, iraj}, title = {Analytical solution of the wave explosion by using the Green's function}, journal = {Iranian Journal of Mechanical Engineering Transactions of ISME}, volume = {20}, number = {3}, pages = {170-184}, year = {2018}, publisher = {ISME}, issn = {2538-4775}, eissn = {}, doi = {}, abstract = {Waves propagation is one of the issues which is considered in defense industry, construction and passive defense. Among the various sources of waves, the explosion is an important factor. After explosion, considerable energy is released in a short time. This energy is emitted into the environment as seismic waves and vibrates the particles in the environment and after that, energy absorption in the environment eventually lead to the weakening of wave propagation and finally wave attenuation. Formulation problems in many branches of science, especially science engineering, leads to differential equations; therefore, faster and more accurately solve the equations of the important issues that underlie many forms of research. In this paper, at first, the analytical solution of two-dimensional wave equation with a source of shock and boundary value using the Green's function method is discussed and then the analysis of explosion process is done by using the Finite Difference Time-Domain Method. The analysis conducted in this paper examine the effect of distance and weight of the explosive.}, keywords = {Waves propagation,wave front,explosion,Green's function}, title_fa = {حل تحلیلی جبهه موج حاصل از انتشار امواج انفجار با استفاده از تابع گرین}, abstract_fa = {انتشار امواج یکی از مهمترین مسائل مطرح شده در صنایع نظامی، پدافند غیرعامل و ساخت وساز می باشد. از میان منابع مختلف تولید امواج، انفجار به عنوان یک عامل مهم حائز اهمیت است. در این مقاله، ابتدا به حل تحلیلی معادله موج دوبعدی با یک منبع ضربه ای و مقدار مرزی با استفاده از روش تابع گرین پرداخته شده و سپس تحلیل فرآیند انفجار با استفاده از روش های عددی و مدل سازی در نرم افزار متلب انجام شده است. تحلیل های انجام شده در این مقاله، تاثیر فاصله انفجار و میزان ماده منفجره را مورد بررسی قرار می دهد.}, keywords_fa = {انتشار امواج,جبهه موج,انفجار,تابع گرین}, url = {https://jmep.isme.ir/article_33772.html}, eprint = {https://jmep.isme.ir/article_33772_6551690e6d15e5b16eb2cdd2b86861b6.pdf} } @article { author = {Esfandyari, Mohammad Javad and Esfahanian, Vahid and حایری یزدی, محمدرضا and Masih-Tehrani, Masoud and Nehzati, Hassan}, title = {Design and Verification of a Model-less Approach for Maintaining Battery Safe Operation in Electric Vehicle Using Hardware-in-the-Loop Simulation}, journal = {Iranian Journal of Mechanical Engineering Transactions of ISME}, volume = {20}, number = {3}, pages = {185-199}, year = {2018}, publisher = {ISME}, issn = {2538-4775}, eissn = {}, doi = {}, abstract = {This paper presents a method for maintaining the battery safe operating voltage region in a hybrid electric vehicle. Using the instantaneous value for the battery voltage in the proposed method, the traction motor maximum torque is limited through an interaction between the BMS and vehicle control unit. Unlike the methods based on battery State of Power (SoP) estimation in which the battery safe operation cannot be guaranteed because of the model-based nature, performance of the proposed method does not rely on the precision of battery modelling and can be used in different life conditions for the battery. In addition, due to low computational costs, the proposed algorithm can be easily implemented on the BMS. Performance of the designed algorithm has been evaluated in a Hardware-in-the-Loop (HiL) test bench for a series hybrid electric bus and compared with the results of SoP estimation based methods. Results indicate the improvement towards maintaining the safe operating voltage region in various life conditions for the battery.}, keywords = {Battery Management System,Battery Safe Operation,Hybrid Electric Vehicle,Hardware-in-the-Loop Simulation}, title_fa = {طراحی و صحه‌گذاری روشی نامبتنی-بر-مدل برای حفظ عملکرد ایمن باتری در خودروی‌برقی بوسیله شبیه‌سازی سخت‌افزار-در-حلقه}, abstract_fa = {این مقاله به ارایه روشی برای حفظ محدوده ولتاژ ایمن باتری در خودروی برقی می‌پردازد. در روش پیشنهادی با استفاده از مقدار لحظه‌ای ولتاژ باتری، محدودسازی حداکثر گشتاور موتور کششی بر اساس یک ارتباط سیگنالینگ بین سیستم مدیریت باتری (BMS) و واحد کنترل خودرو انجام می‌شود. عملکرد روش پیشنهادی مبتنی بر دقت مدل‌سازی باتری نیست و برای شرایط مختلف عمر باتری قابل استفاده است. عملکرد روش پیشنهادی بوسیله بستر تست سخت‌افزار-در-حلقه برای یک اتوبوس هیبرید الکتریکی سری مورد ارزیابی قرار گرفته است و نتایج شبیه‌سازی حاکی از بهبود عملکرد نسبت به روش‌های متداول موجود برای شرایط مختلف عمر باتری است.}, keywords_fa = {سیستم مدیریت باتری,عملکرد ایمن باتری,خودروی هیبرید الکتریکی,شبیه‌سازی سخت‌افزار-در-حلقه}, url = {https://jmep.isme.ir/article_33773.html}, eprint = {https://jmep.isme.ir/article_33773_fab587b0a975658c431ee82e2271abf3.pdf} } @article { author = {Bagheri Tadi, Hamid Reza and Kiani, Yaser}, title = {Thermoelastic Analysis of Rotating FGM Cylindrical Vessels In an Elastic Medium}, journal = {Iranian Journal of Mechanical Engineering Transactions of ISME}, volume = {20}, number = {3}, pages = {200-212}, year = {2018}, publisher = {ISME}, issn = {2538-4775}, eissn = {}, doi = {}, abstract = {In the present research, stress analysis of a functionally graded material cylindrical pressure vessel subjected to the simultaneous action of thermal loading, rotation and internal pressure is performed. Also it is assumed that vessel in located in an elastic medium which is designated according to the Winkler model. Except for Poisson’s ratio, all of the thermomechanical properties of the vessel are assumed to follow a power law model and vary across the radius of the vessel. Heat conduction equation and Navier equation which govern the temperature and radial displacement distribution across the radius of vessel are established and solved analytically. Closed form expressions are obtained for temperature distribution, radial displacement profile, strains and stresses components in the vessel. Parametric studies are provided to explore the effects of rotation and foundation stiffness on the structural responses of the vessel. It is shown that, foundation stiffness, power law index of the properties and angular speed all affect the stresses and displacement components of the vessel, significantly.}, keywords = {Cylindrical vessel,Functionally graded material,Navier equation,rotational inertia}, title_fa = {تحلیل ترموالاستیک مخازن دوار استوانه‏ ای هدفمند درون بستر الاستیک}, abstract_fa = {در تحقیق حاضر به بررسی یک مخزن استوانه‏ای ساخته شده از مواد هدفمند که در معرض تغییرات درجه حرارت، اینرسی دورانی و همچنین فشار داخی قرار دارد، پرداخته شده است. مخزن استوانه‏ای درون یک بستر الاستیک قرار گرفته است. کلیه خواص ترموالاستیک وابسته به شعاع بوده و با استفاده از مدل توانی ارائه شده‏اند. معادله انتقال حرارت و معادله ناویر حاکم بر جابجایی مخزن در راستای شعاعی تشکیل شده و به صورت تحلیلی و جواب بسته حل شده‏اند. با به دست آوردن توابع توزیع دما و جابجایی، عبارتهایی برای توزیع کرنش و تنش در مخزن به دست آمده است.}, keywords_fa = {مخزن استوانه‏ای,ماده هدفمند,معادله ناویر,اینرسی دورانی}, url = {https://jmep.isme.ir/article_33774.html}, eprint = {https://jmep.isme.ir/article_33774_504d83653fe0535310378a0a499ed5aa.pdf} }