ORIGINAL_ARTICLE
تحلیل عددی خصوصیات جریان هوا در دودکش خورشیدی با حضور لایه گیاهی
امروزه افزایش تقاضا برای انرژی از یک سو و کاهش منابع فسیلی از سوی دیگر اهمیت استفاده از منابع انرژی تجدیدپذیر را بیش از پیش نمایان میکند. دودکش خورشیدی بهعنوان یکی از راههای استفاده از انرژی خورشیدی برای تولید برق است. این ایده به دلیل بالا بودن سطح جذب انرژی خورشیدی و همچنین مزایای استفاده از هوا به عنوان جاذب، توجه محققین را به خود جذب نموده است. ولی این سیستم در حال حاضر صرفه اقتصادی پایینی دارد. در این مطالعه برای حل این مشکل، پرورش گیاه در کلکتور به منظور افزایش بهرهوری اقتصادی پیشنهاد و شبیهسازی عددی شد و اثرات هندسی و فیزیکی گیاه بر جریان هوا مورد بررسی قرار گرفت. تاکنون کشت گیاه در کلکتور برای رفع مشکل صرفه اقتصادی پایین به صورت دقیق مورد بررسی قرار نگرفته است. برای اعتبار سنجی مدل ابتدا مدل آزمایشی ساخته شده در مانزانارس اسپانیا مدلسازی و سرعت و اختلاف دمای ایجاد شده در جریان هوا بین ورودی و خروجی کلکتور محاسبه شد. نتایج بدست آمده از حل عددی مطابقت بسیار خوبی با نتایج آزمایشگاهی را نشان داد و خطا کمتر از 5 درصد بود. در ادامه لایه گیاهی بهصورت محیط متخلخل در کف کلکتور مدلسازی و تاثیر آن بر سرعت جریان و اختلاف دمای ایجاد شدهدر عدد رایلی Ra=10^11 بررسی شد. مشاهده شد که در خروجی کلکتور سرعت چریان تقریبا 2.5 درصد کاهش و اختلاف دما تقریبا 2 درصد افزایش یافت . بنابراین میتوان ادعا کرد که با کشت سطح وسیعی از زمین کلکتور با یک گیاه با صرفه اقتصادی بالا میتوان مشکل اقتصادی سیستم دودکش خورشیدی را برطرف نمود بدون اینکه تاثیر منفی چشمگیری بر خصوصیات جریان داشته باشد.
https://jmep.isme.ir/article_22954_86c7587d40042662c97b74bea3abe418.pdf
2016-02-20
6
22
انرژی خورشیدی
دودکش خورشیدی
محیط متخلخل
شبیه سازی عددی
انتقال حرارت
آرش
میرعبدالله لواسانی
arashlavasani@iauctb.ac.ir
1
استادیار گروه مهندسی مکانیک، دانشگاه آزاد اسلامی، واحد تهران مرکزی
LEAD_AUTHOR
مهرداد
محمدی
mehrdadmohammadi.mm@gmail.com
2
دانشجوی کارشناسی ارشد، گروه مهندسی مکانیک، دانشگاه آزاد اسلامی، واحد تهران مرکزی
AUTHOR
رامین
مهدیپور
mehdipour@tafreshu.ac.ir
3
استادیار دانشکده مهندسی مکانیک، دانشگاه تفرش
AUTHOR
[1] Haaf, W., “Solar Chimneys, Part II: Preliminary Test Results from the Manzanares Pilot Plant”, International Journal of Solar Energy, Vol. 2, pp. 141-16, (1984).
1
[2] Bernardes, M., Vob, A., and Weinrebe, G., “Thermal and Technical Analyses of Solar Chimneys”, Solar Energy, Vol. 75, pp. 511–524, (2003).
2
[3] Zhou, X., Yang, J., and Guoxiang Hou, B., “Experimental Study of Temperature Field in a Solar Chimney Power Setup”, Applied Thermal Engineering, Vol. 27, pp. 2044–2050, (2007).
3
[4] Tingzhen, M., Wei, L., Xiong Yanbin, X., Xuhu, G., and Yuan, P., “Numerical Simulation of the Solar Chimney Power Plant Systems Coupled with Turbine”, Renewable Energy, Vol. 33, pp. 897–905, (2008).
4
[5] Ketlogetswe, C., Fiszdon, J., and Seabe, O., “Solar Chimney Power Generation Projectthe Case for Botswana”, Renewable and Sustainable Energy Reviews, Vol. 12, pp. 2005–2012, (2008).
5
[6] Petela, R., “Thermodynamic Study of a Simplified Model of the Solar Chimney Power Plant”, Solar Energy, Vol. 83, pp. 94–107, (2009).
6
[7] Kasaeian, A.B., Heidari, E., and Nasiri Vatan, Sh., “Experimental Investigation of Climatic Effects on the Efficiency of a Solar Chimney Pilot Power Plant”, Renewable and Sustainable Energy Reviews, (2011).
7
[8] Xu, G., Ming, T., Pan, Y., Meng, F., and Zhou, C., “Numerical Analysis on the Performance of Solar Chimney Power Plant System”, Energy Conversion and Management, Vol. 52, pp. 876–883, (2011).
8
[9] Sangi, R., Amidpour, M., and Hosseinizadeh, B., “Modeling and Numerical Simulation of Solar Chimney Power Plants”, Solar Energy, Vol. 85, pp. 829–838, (2011).
9
[10] Hamdan, M., “Analysis of a Solar Chimney Power Plant”, Renewable Energy, Vol. 36, pp. 2593-2598, (2011).
10
[11] Li, J., Guo, P., and Wang, Y., “Effects of Collector Radius and Chimney Height on Power Output of a Solar Chimney Power Plant with Turbines”, Renewable Energy, Vol.47, pp. 21-28, (2012).
11
[12] Sharma, P.K., Tiwari, G.N., and Sorayan, V.P.S., “Temperature Distribution in Diferent Zones of the Micro-climate of a Greenhouse: a Dynamic Model”, Energy Conversion & Management, Vol. 40, pp. 335-348, (1999).
12
[13] Tong, G., Christopher, D.M., and Li, B., “Numerical Modelling of Temperature Variations in a Chinese Solar Greenhouse”, Computers and Electronics in Agriculture, Vol. 68, pp. 129–139, (2009).
13
[14] Nicolau, V., and Maluf, F., “Determination of Radiative Properties of Commercial Glass”, the 18th Conference on Passive and Low Energy Architecture, Florianopolis –Brazil, 7-9, (2001).
14
[15] Quirion, S., Villeneuve, S., LeBlanc, D., and Delaquis, P., “Thermophysical Properties and Thermal Behavior of Leafy Vegetables Packaged in Clamshells”, Journal of Food Engineering, Vol. 113, pp. 27-32, (2012).
15
ORIGINAL_ARTICLE
تخمین پروفیل رسوب در لوله یک مبدل حرارتی با استفاده از روش انتقال حرارت معکوس گرادیان مزدوج با مساله الحاقی
یکی از عوامل مؤثر در کاهش راندمان مبدل حرارتی در طول دوره کارکرد رسوب است. رسوب به صورت یک لایه بر روی یک طرف یا هر دو طرف سطح انتقال حرارت قرار میگیرد و در اثر مقاومت حرارتی که از خود نشان میدهد باعث کاهش انتقال حرارت عبوری از سطح میشود. در نتیجه راندمان مبدل حرارتی را کاهش میدهد. بر همین اساس اندازهگیری رسوب از اهمیت فوق العادهای برخوردار است. با اندازهگیری دقیق رسوب و اطمینان از این که رسوب از حد مجاز خود فراتر رفته است یا نه می توان عملیات رسوبزدایی و پاکسازی را انجام داد. در این تحقیق از روش گرادیان مزدوج با مسأله الحاقی CGM جهت تخمین پروفیل لایهی رسوب نامشخص بر روی دیواره درونی لوله، استفاده شده است. نتایج نشان میدهد که برای 2 نوع پروفیل رسوب خطی و زیگزاگ که در این پژوهش مورد بررسی قرار گرفته، تخمین به بهترین صورت ممکن صورت گرفته است و نتایج بسیار خوبی بدست آمده است. تکنیکی که در این تحقیق ارائه شده میتواند زمانی که ضخامت رسوب از حد مجاز عبور کرده باشد، به عنوان یک سیستم هشداری جهت تمیزکاری لوله مبدل حرارتی مورد استفاده قرار گیرد.
https://jmep.isme.ir/article_22955_e46863237461e5bbb8d56f26d65a4d82.pdf
2016-02-20
23
45
مبدل حرارتی
رسوب
روش گرادیان مزدوج با مسأله الحاقی
کورش
گودرزی
kgoudarzi@yu.ac.ir
1
دانشیار گروه مهندسی مکانیک، دانشگاه یاسوج
LEAD_AUTHOR
امین
موسائی
mosaie@yu.ac.ir
2
استادیار گروه مهندسی مکانیک، دانشگاه یاسوج
AUTHOR
علیرضا
نامداری
ar.namdari@gmail.com
3
دانشجوی کارشناسی ارشد، گروه مهندسی مکانیک، دانشگاه یاسوج
AUTHOR
[1] Guerin, R., Ronse, G., Bouvier, L., Debreyne, P., and Delaplace, G., “Structure and Rate of Growth of Whey Protein Deposit from in Situ Electrical Conductivity During Fouling in a Plate Heat Exchanger”, Chemical Engineering Science, Vol. 62, pp. 1948–1957, (2007).
1
[2] Hesselgreaves, J. E., “An Approach to Fouling Allowances in the Design of Compact Heat Exchangers”, Applied Thermal Engineering, Vol. 22, pp. 755–762, (2002).
2
[3] Mohanty, D. K., and Singru, P. M., “Numerical Method for Heat Transfer and Fouling Analysis of a Shell and Tube Heat Exchanger using Statistical Analysis”, Korean J. Chem. Eng, Vol. 29, pp. 1144-1150, (2012).
3
[4] Merheb, B., Nassar, G., Nongaillard, B., Delaplace, G., and Leuliet, J. C., “Design and Performance of a Low-frequency Non-intrusive Acoustic Technique for Monitoring Fouling in Plate Heat Exchangers”, Journal of Food Engineering, Vol. 82, pp. 518–527, (2007).
4
[5] Wallhaußer, E., Hussein, M. A., and Becker, T., “Detection Methods of Fouling in Heat Exchangers in the Food Industry”, Food Control, Vol. 27, pp. 1–10, (2012).
5
[6] Lalot, S., and Palsson, H., “Detection of Fouling in a Cross-flow Heat Exchanger using a Neural Network Based Technique”, International Journal of Thermal Sciences, Vol. 49, pp. 675-679, (2010).
6
[7] Mohanty, D. K., and Singru, P. M., “Use of C-factor for Monitoring of Fouling in a Shell and Tube Heat Exchanger”, Energy, Vol. 36, pp. 2899-2904, (2011).
7
[8] Jonsson, G. R, Lalot, S., Palsson, O. P., and Desmet, B., “Use of Extended Kalman Filtering in Detecting Fouling in Heat Exchangers”, International Journal of Heat and Mass Transfer, Vol. 50, pp. 2643–2655, (2007).
8
[9] Ozisik, M. N., and Orlande, H. R. B., "Inverse Heat Transfer: Fundamental and Applications", 2th ed., Rivard, (2000).
9
[10] Hoffmann, K. A., and Chiange, S. T., "Computational Fluid Dynamics for Engineers", 5th ed., Wichita, Kansas, (2000).
10
ORIGINAL_ARTICLE
مطالعه عددی تاثیر میدان مغناطیسی غیر یکنواخت محوری بر رشد حباب در جریان جوششی نانو سیال مغناطیس شونده داخل یک میکروکانال
در این پژوهش، چگونگی رشد حباب در فرآیندد جوشش هستهای آب خالص و فروسیال (سیال حاوی نانوذرات اکسید آهن) بصورت عددی و با استفاده از روش حجم محدود و مدل VOF مورد بررسی قرار گرفته است. پس از اعتبار سنجی نتایج بدس آمده با نتایج موجود در ادبیات فن، تاثیر اعمال میدانهای مغناطیسی غیریکنواخت محوری بر رشد یک حباب در فرآیند جوشش نانوسیال مغناطیس شونده بررسی شده است. با توجه به نتایح بدست آمده، در حضور میدان مغناطیسی با گرادیانهای مثبت، انتقال حرارت از دیوارهها بیشتر شده و گرمای دیوارهها بهتر انتقال مییابد و این موضوع سبب کاهش رشد حباب میشدود در حالیکه میدان با گرادیان منفی، باعث افزایش رشد حباب میشود. در واقع استفاده لز میدانهای مغناطیسی با گرادیان مثبت سبب افدزایش بازدهی میکروسیستمهای خنک کننده میشود.
https://jmep.isme.ir/article_22956_de9421b79ea29e2303ce48426ed8ec3e.pdf
2016-02-20
46
68
جوشش نانوسیال
میدان مغناطیسی غیریکنواخت
میکروکانال
موسی
محمدپورفرد
mohammadpour@azaruniv.edu
1
دانشیار گروه مهندسی مکانیک، دانشگاه شهید مدنی آذربایجان
LEAD_AUTHOR
مهدی
قربانی فیروزسالاری
bcs_ghorbani@yahoo.com
2
کارشناس ارشد، گروه مهندسی مکانیک،دانشگاه شهید مدنی آذربایجان
AUTHOR
[1] Rosensweing, R. E., and Roland, E., "Ferrohydrodynamics", Cambridge University Press, New York, (1985).
1
[2] Kandlikar, S.G., Garimella, S., Li, D., Colin, S., and King, M.R., "Heat Transfer and Fluid Flow in Minichannels and Microchannels", Elsvier, UK, (2006).
2
[3] Mukherjee, A., and Kandlikar, S.G., "Numerical Simulation of Growth of a Vapor Bubble During Flow Boiling of Water in a Microchannel", International Conference on Microchannels and Minichannels, ASME, New York, USA, pp. 565-572, (2004).
3
[4] Wu, Y., Yang, C., and Yuan, X., "Numerical Simulation of Heat Transfer in Nucleate Pool Boiling, Huagong Xuebao/J. Chem. Ind. Eng. (China) Vol. 53, pp. 479–486, (2002).
4
[5] Mukherjee, A., Kandlikar, S.G., and Edel, Z.J., "Numerical Study of Bubble Growth and Wall Heat Transfer During Flow Boiling in a Microchannel", International Journal of Heat and Mass Transfer, Vol. 54, pp. 3702–3718, (2011).
5
[6] Kandlikar, S.G., "Nucleation Characteristics and Stability Considerations During Flow Boiling in Microchannels", Exp. Thermal Fluid Sci. Vol. 30, pp. 441–447, (2006).
6
[7] Lee, P.C., Tseng, F.G., and Pan, C., "Bubble Dynamics in Microchannels", Part I, Single Microchannel. Int. J. Heat Mass Transfer, Vol. 47, pp. 5575–5589, (2004).
7
[8] Young, N.O., Goldstein, J.S., and Block, M.J., "The Motion of Bubbles in a Vertical Temperature Gradient", J. Fluid Mech. Vol. 6, pp. 350–356, (1959).
8
[9] Cornwell, K., and Kew, P.A., "Boiling in Small Parallel Channels", In: Proceedings of CEC Conference on Energy Efficiency in Process Technology, Elsevier, Applied Sciences, Athens, pp. 624-638, (1992).
9
[10] Junhong, L., Jianming, G., Zhiwei, L., and Hui, L., "Experiments and Mechanism Analysis of Pool Boiling Heat Transfer Enhancement with Water-based Magnetic Fluid", International Journal of Heat and Mass Transfer, Vol. 41, pp. 170-175, (2004).
10
[11] Hamilton, R.L., and Crosser, O.K., , "Thermal Conductivity of Heterogeneous Twocomponent System", I & EC Fundamentals, Vol. 1, pp. 187-191, (1962).
11
[12] Khanafer, K., and Vafai, M.," Lightstone, Buoyancy-driven Heat Transfer Enhancement in a Two Dimensional Enclosure Utilizing Nanofluids", International Journal of Heat Mass Transfer, Vol. 46, pp. 3639–3653, (2003).
12
ORIGINAL_ARTICLE
بررسی تجربی استفاده از دیوارهای بادشکن برای افزایش دبی ورودی برج هلر تحت وزش باد
وزش باد، یکی از عوامل محیطی نامطلوب بر عملکرد حرارتی برجهای هلر میباشد. در این مطالعه تجربی، با استفاده از یک مدل همدمای برج هلر در تونل باد، تاثیر وجود دیوارهای بادشکن در بهبود دبی ورودی به برج در شرایط وزش باد بررسی گردیده است. دیوارهای بادشکن در ابعاد و زوایای مختلف در اطراف مدل نصب و کارایی آنها در چندین زاویه وزش باد مطالعه شده است. بر اساس نتایج، استفاده از دیوارهای بادشکن، تا 30 % دبی ورودی به برج را افزایش میدهد. همچنین با زیاد شدن سرعت باد، تاثیر طول دیوار بادشکن بر دبی ورودی افزایش مییابد. علاوه بر این، تاثیر زاویه وزش باد بر عملکرد دیوارهای بادشکن تا 30 درجه نسبت به قطر عمود بر باد، محسوس نیست.
https://jmep.isme.ir/article_22957_70d23df4a20aaf9562099d241e61c5bb.pdf
2016-02-20
69
84
بررسی تجربی
برج خنککن هلر
تونل باد
دیوار بادشکن
محمدعلی
اردکانی
ardekani@irost.ir
1
دانشیار، پژوهشکده مهندسی مکانیک، سازمان پژوهشهای علمی و صنعتی ایران
LEAD_AUTHOR
محسن
مزیدی
mazidi@irost.ir
2
دانشجوی دکتری، پژوهشکده مهندسی مکانیک، سازمان پژوهشهای علمی و صنعتی ایران
AUTHOR
فواد
فرهانی
f.farhani@irost.ir
3
استادیار پژوهشکده مهندسی مکانیک، سازمان پژوهشهای علمی و صنعتی ایران
AUTHOR
[1] Ardekani, M.A., “Effects of Cross Wind Conditions on Efficiency of Heller Dry Cooling Tower”, Experimental Heat Transfer: A Journal of Thermal Energy Generation, Transport, Storage, and Conversion, Vol. 28, Issue. 4, pp. 344-353, (2015).
1
[2] Ardekani, M.A., and Ranjbar, M.A., “Field Study on Airflow Pattern through Radiator of Heller Dry Cooling Tower”, Modares Mechanical Engineering, Vol. 13, No. 11, pp. 30-40, (2013).
2
[3] Wei, Q., “A Study of the Unfavorable Effects of Wind on the Cooling Efficiency of Dry Cooling Towers”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 54, pp. 633-643, (1995).
3
[4] Du Preez, A.F., and Kroger, D.G., “Effect of Wind on Performance of a Dry-cooling Tower”, Heat Recovery Systems and CHP Journal, Vol. 13, Issue. 2, pp. 139-146, (1993).
4
[5] Su, M.D., and Tang, G.F., “Numerical Simulation of Fluid Flow and Thermal Performance of a Dry-cooling Tower under Cross Wind Condition”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 74, pp. 289-306, (1998).
5
[6] Zhao, Y.B., “Numerical Study on the Cooling Performance of Dry Cooling Tower with Vertical Two-pass Column Radiators under Crosswind”, Applied Thermal Engineering, Vol. 75, pp. 1106-1117, (2015).
6
[7] Du Preez, A.F., and Kroger, D.G., “The Effect of the Heat Exchanger Arrangement and Wind Break Walls on the Performance of Natural Draft Dry Cooling Towers Subjected to Cross Winds”, International Journal of Wind Engineering and Industrial Aerodynamics, Vol. 58, No. 1, pp. 293-303, (1995).
7
[8] Madadnia, M., “Effect of Wind Break Walls on Performance of a Cooling Tower Model”, Mechanical and Aerospace Engineering Journal, Vol. 3, No. 4, pp. 61-67, (2008).
8
[9] Al-Waked, R., and Behnia, M., “The Effect of Windbreak Walls on the Thermal Performance of Natural Draft Dry Cooling Towers”, Journal of Heat Transfer Engineering, Vol. 28, No. 8, pp. 50-62, (2005).
9
[10] Raine, J., and Stevenson, D., “Wind Protection by Model Fences in a Simulated Atmospheric Boundary Layer”, International Journal of Wind Engineering and Industrial Aerodynamics, Vol. 2, No. 1, pp. 159-180, (1977).
10
[11] Gandmer, J., “The Aerodynamic Characteristics of Windbreaks, Resulting in Empirical Design Rules”, International Journal of Wind Engineering and Industrial Aerodynamics, Vol. 7, No. 1, pp. 15-36, (1981).
11
[12] Lu, Y., “The Influence of Windbreak Wall Orientation on the Cooling Performance of Small Natural Draft Dry Cooling Towers”, International Journal of Heat and Mass Transfer, Vol. 79, pp. 1059-1069, (2014).
12
[13] EGI, “The Heller Systems”, Report Ref. No. 8325-LK, (1984).
13
[14] Ardekani, M. A., “Design and Application of Low Speed Wind Tunnel”, 1st Edition, Khaje Nasir Toosi University Publication, Tehran, (2009). (In Persian)
14
ORIGINAL_ARTICLE
مطالعه تحلیلی و تجربی انتقال حرارت جوشش هستهای استخری بر روی سطوح مسی آب دوست
در این مقاله، تاثیر میزان آبدوستی سطح بر جوشش هستهای استخری آب تحت فشار اتمسفر به صورت تحلیلی مدل گردیده و به صورت تجربی مورد صحتسنجی قرار میگیرد. مدل تحلیلی ارائه شده بر خلاف مدل های قبلی، تغییرات زاویه تماس سیال با سطح را در حین رشد حباب درنظر میگیرد. مقایسه منحنی جوشش استخری پیشبینی شده توسط مدل بهبودیافته با نتایج آزمایشگاهی دیگران و مدل پیشین، تطابق بهتر نتایج را نشان داد. علاوه بر این، سطوح آبدوست (با زوایای تماس 34، 22 و کمتر از 10) توسط استغراق مس در محلول آبی هیدروکسید سدیم و پرسولفات پتاسیم در زمانهای مختلف (30، 60 و 180 دقیقه) ساخته شده و نتایج آزمون جوشش با پیشبینی مدل مقایسه میگردد. بر اساس نتایج تجربی، عملیات سطحی به کار رفته در این پژوهش به عنوان روشی مؤثر در افزایش ترشوندگی سطح مسی میباشد و آب دوستی بیشتر این سطوح باعث افزایش ضریب انتقال حرارت جوشش استخری نسبت به سطح معمولی میگردد.
https://jmep.isme.ir/article_22958_5641ada64e0b2d2d9c000e6d80189477.pdf
2016-02-20
85
104
جوشش هسته ای استخری
سطح آبدوست
مدل انتقال حرارت
زاویه تماس دینامیکی
سید سینا
ارشدی
sina_arshadi@mecheng.iust.ac.ir
1
کارشناس ارشد، دانشکده مهندسی مکانیک، دانشگاه علم و صنتعت ایران
AUTHOR
حمید
صفاری
saffari@iust.ac.ir
2
دانشیار دانشکده مهندسی مکانیک، دانشگاه علم و صنعت ایران
AUTHOR
امیر
میرزاقیطاقی
a_m_gheitaghy@mecheng.iust.ac.ir
3
دانشجوی دکتری، دانشکده مهندسی مکانیک، دانشگاه علم و صنعت ایران
LEAD_AUTHOR
[1] Jones, B. J., McHale, J. P., and Garimella, S. V., "The Influence of Surface Roughness on Nucleate Pool Boiling Heat Transfer", Journal of Heat Transfer, Vol. 131, No. 12, pp. 121-129, (2009).
1
[2] Phan, H. T., Caney, N., Marty, P., Colasson, S., and Gavillet, J., "How Does Surface Wettability Influence Nucleate Boiling?", C. R. Mecanique 337, pp. 251–259, (2009).
2
[3] Han, C., and Griffith, P., "The Mechanism of Heat Transfer in Nucleate Pool Boiling", International Journal of Heat and Mass Transfer, Vol. 8, No. 6, pp. 887-914, (1965).
3
[4] Mikic, B., and Rohsenow, W., "A New Correlation of Pool-boiling Data Including the Effect of Heating Surface Characteristics", Journal of Heat Transfer, Vol. 91, No. 2, pp. 245-250, (1969).
4
[5] Judd, R., and Hwang, K., "A Comprehensive Model for Nucleate Pool Boiling Heat Transfer Including Microlayer Evaporation", Journal of Heat Transfer, Vol. 98, No. 4, pp. 623-629, (1976).
5
[6] Paul, D., and Abdel-Khalik, S., "A Statistical Analysis of Saturated Nucleate Boiling Along a Heated Wire", International Journal of Heat and Mass Transfer, Vol. 26, No. 4, pp. 509-519, (1983).
6
[7] Benjamin, R., and Balakrishnan, A., "Nucleate Pool Boiling Heat Transfer of Pure Liquids at Low to Moderate Heat Fluxes", International Journal of Heat and Mass Transfer, Vol. 39, No. 12, pp. 2495-2504, (1996).
7
[8] Yu, B., and Cheng, P., "A Fractal Model for Nucleate Pool Boiling Heat Transfer", Journal of Heat Transfer, Vol. 124, No. 6, pp. 1117-1124, (2002).
8
[9] Li, Y. Y., Liu, Z.H., and Wang, G.S., "A Predictive Model of Nucleate Pool Boiling on Heated Hydrophilic Surfaces", International Journal of Heat and Mass Transfer, Vol. 65, pp. 789-797, (2013).
9
[10] Del Valle, V. H., and Kenning, D., "Subcooled Flow Boiling at High Heat Flux", International Journal of Heat and Mass Transfer, Vol. 28, No. 10, pp. 1907-1920, (1985).
10
[11] Benjamin, R., and Balakrishnan, A., "Nucleation Site Density in Pool Boiling of Saturated Pure Liquids: Effect of Surface Microroughness and Aurface and Liquid Physical Properties", Experimental Thermal and Fluid Science, Vol. 15, No. 1, pp. 32-42, (1997).
11
[12] Phan, H. T., Caney, N., Marty, P., Colasson, S., and Gavillet, J., "Surface Wettability Control by Nanocoating: the Effects on Pool Boiling Heat Transfer and Nucleation Mechanism", International Journal of Heat and Mass Transfer, Vol. 52, No. 23, pp. 5459-5471, (2009).
12
[13] Zhao, Y.H., Masuoka, T., and Tsuruta, T., "Unified Theoretical Prediction of Fully Developed Nucleate Boiling and Critical Heat Flux Based on a Dynamic Microlayer Model", International journal of heat and mass transfer, Vol. 45, No. 15, pp. 3189-3197, (2002).
13
[14] Sernas, V., and Hooper, F., "The Initial Vapor Bubble Growth on a Heated Wall During Nucleate Boiling", International Journal of Heat and Mass Transfer, Vol. 12, No. 12, pp. 1627-1639, (1969).
14
[15] Phan, H. T., " Effects of Nano-and Micro-Surface Treatments on Boiling Heat Transfer", PhD Thesis, Department of Mechanical Engineering, Institut National Polytechnique de Grenoble-INPG, (2010).
15
[16] Zuber, N., "The Region of Isolated Bubbles and the Similarity with Natural Convection", International Journal of Heat and Mass Transfer, Vol. 6, No. 1, pp. 53-78, (1963).
16
[17] Hsu, C. C., and Chen, P.H., "Surface Wettability Effects on Critical Heat Flux of Boiling Heat Transfer using Nanoparticle Coatings", International Journal of Heat and Mass Transfer, Vol. 55, No. 13-14, pp. 3713-3719, (2012).
17
[18] Kwark, S. M., Moreno, G., Kumar, R., Moon, H., and You, S. M., "Nanocoating Characterization in Pool Boiling Heat Transfer of Pure Water", International Journal of Heat and Mass Transfer, Vol. 53, No. 21, pp. 4579-4587, (2010).
18
[19] Li, C., Wang, Z., Wang, P. I., Peles, Y., Koratkar, N., and Peterson, G., "Nanostructured Copper Interfaces for Enhanced Boiling", Small, Vol. 4, No. 8, pp. 1084-1088, (2008).
19
[20] Saeidi, D., and Alemrajabi, A., "Experimental Investigation of Pool Boiling Heat Transfer and Critical Heat Flux of Nanostructured Surfaces", International Journal ofHeat and Mass Transfer, Vol. 60, pp. 440-449, (2013).
20
[21] Min, J., Wu, X., Shen, L., and Ga, F., "Hydrophilic Treatment and Performance Evaluation of Copper Finned Tube Evaporators", Applied Thermal Engineering, Vol. 31, pp. 2936-2942, (2011).
21