[1] Ramsey, J.W., and Goldstein, R.J., “Interaction of a Heated Jet with a Deflecting Stream”, Journal of Heat Transfer, Vol. 93, No. 4, pp. 365-372, (1971).
[2] Sinha, A.K., Bogard, D.G., and Crawford, M.E., “Film-cooling Effectiveness Downstream of a Single Row of Holes with Variable Density Ratio”, Journal of Turbomachinery, Vol. 113, No. 3, pp. 442-449, (1991).
[3] An, B.T., Liu, J.J., Zhang, X.D., Zhou, S.J., and Zhang, C., “Film Cooling Effectiveness Measurements of a Near Surface Streamwise Diffusion Hole”, International Journal of Heat and Mass Transfer, Vol. 103, pp. 1-13, (2016).
[4] Ghorab, M.G., Hassan, I.G., and Lucas, T., “An Experimental Investigation of Film Cooling Performance of Louver Scheme”, International Journal of Heat and Mass Transfer, Vol. 54, No. 7-8, pp. 1387-1399, (2011).
[5] Chen, S.P., Chyu, M.K., and Shih, T.I.P., “Effects of Upstream Ramp on the Performance of Film Cooling”, International Journal of Thermal Sciences, Vol. 50, No. 6, pp. 1085-1094, (2011).
[6] Heidmann, J.D., and Ekkad, S., “A Novel Antivortex Turbine Film-cooling Hole Concept”, Journal of Turbomachinery, Vol. 130, No. 3, pp. 031020, (2008).
[7] Repko, T.W., Nix, A.C., Uysal, S.C., and Sisler, A.T., “Flow Visualization of Multi-hole Film Cooling Flow under Varying Freestream Turbulence Levels”, J. Flow Control Meas. Visualization, Vol. 4, pp. 13-29, (2016).
[8] Ramesh, S., Ramirez, D.G., Ekkad, S.V., and Alvin, M.A., “Analysis of Film Cooling Performance of Advanced Tripod Hole Geometries with and without Manufacturing Features”, International Journal of Heat and Mass Transfer, Vol. 94, pp. 9-19, (2016).
[9] Schmidt, D.L., Sen, B., and Bogard, D.G., “Film Cooling with Compound Angle Holes: Adiabatic Effectiveness”, Journal of Turbomachinery, Vol. 118, No. 4, pp. 807-813, (1996).
[10] Bazdidi-Tehrani, F., and Pezeshkpour, P., “Film Cooling Flow by Double Rows of Compound Angle and Compound Angle Shaped Holes”, In ASME Turbo Expo 2013: Turbine Technical Conference and Exposition (pp. V03BT13A048-V03BT13A048). American Society of Mechanical Engineers, San Antonio, Texas, USA, (2013).
[11] Wu, H., Cheng, H., Li, Y., Rong, C., and Ding, S., “Effects of Side Hole Position and Blowing Ratio on Sister Hole Film Cooling Performance in a Flat Plate”, Applied Thermal Engineering, Vol. 93, pp. 718-730, (2016).
[12] Khajehhasani, S., and Jubran, B.A., “A Numerical Evaluation of the Performance of Film Cooling from a Circular Exit Shaped Hole with Sister Holes Influence”, Heat Transfer Engineering, Vol. 37, No. 2, pp. 183-197, (2016).
[13] White, F.M., and Corfield, I., “Viscous Fluid Flow”, Vol. 3, New York, McGraw-Hill, (2006).
[14] Naghashnejad, M., Amanifard, N., and Deylami, H.M., “A Predictive Model Based on a 3-D Computational Approach for Film Cooling Effectiveness Over a Flat Plate using GMDH-type Neural Networks”, Heat and Mass Transfer, Vol. 50, No. 1, pp. 139-149, (2014).
[15] Launder, B.E., and Sharma, B.I., “Application of the Energy-dissipation Model of Turbulence to the Calculation of Flow Near a Spinning Disc”, Letters in Heat and Mass Transfer, Vol. 1, No. 2, pp. 131-137, (1974).
[16] Ansys Fluent User’s Manual, Version 15, (2013).
[17] Walters, D.K., and Leylek, J.H., “A Systematic Computational Methodology Applied to a Three–dimensional Film–cooling Flowfield”, In ASME (1996) International Gas Turbine and Aeroengine Congress and Exhibition (pp. V004T09A040-V004T09A040), American Society of Mechanical Engineers, Birmingham, UK, 10-13 June, (1996).
)
