بررسی اثر فرآیند پرس در قالب شیار محدود (CGP) بر روی ورق های مسی

نوع مقاله : مقاله علمی پژوهشی

نویسندگان

1 کاشان*مهندسی مکانیک

2 دانشگاه کاشان

3 دانشگاه آزاد اسلامی واحد جاسب

چکیده

در این تحقیق فرآیند پرس در قالب شیار محدود مطالعه شده و تاثیر این فرآیند بر خواص مکانیکی و ریزساختار ورق‌های مسی مورد بررسی قرار گرفته است. جهت بررسی خواص مکانیکی از آزمون‌های تست کشش تک محوره و سختی ویکرز و برای ارزیابی ریزساختارها از میکروسکوپ‌ نوری استفاده شده است. بررسی نتایج نشان داد با استفاده از فرآیند پرس در قالب شیار محدود، استحکام و سختی نمونه‌ها به طور چشم‌گیری افزایش می‌یابد. همچنین تصاویر تهیه شده با استفاده از میکروسکوپ‌ نوری نشان داد فرآیند پرس در قالب شیار محدود بر ریزدانه نمودن ساختار بسیار موثر می‌باشد.

کلیدواژه‌ها


[1]   Honarpisheh, M., Haghighat, E., and Kotobi, M., "Investigation of Residual Stress and Mechanical Properties of Equal Channel Angular Rolled St12 Strips", Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials Design and Applications, https://doi.org/10.1177/1464420716652436, (2016).
 
[2]    Kotobi, M., and Honarpisheh, M., "Uncertainty Analysis of Residual Stresses Measured by Slitting Method in Equal-channel Angular Rolled Al-1060 Strips", The Journal of Strain Analysis for Engineering Design, Vol. 52, No. 2, pp. 83-92, (2017).
 
[3]     Lee, J.W., and Park, J.J., “Numerical and Experimental Investigations of Constrained Groove Pressing and Rolling for Grain Refinement”, Journal of Materials Processing Technology, Vol. 130–131, pp.  208–213, (2002).
 
[4]     Krishnaiah, A., Chakkingal, U., and Venugopal, P., “Production of Ultrafine Grain Sizes in Aluminium Sheets by Severe Plastic Deformation using the Technique of Groove Pressing”, Scripta Materialia, Vol. 52, pp. 1229–1233, (2005)
 
[5]     Krishnaiah, A., Chakkingal, U., and Venugopal, P., “Applicability of the Groove Pressing Technique for Grain Refinement in Commercial Purity Copper”, Materials Science and Engineering A, Vol. 410–411, pp. 337–340, (2005).
 
[6]     Peng, K., Su, L, Shaw, L.L., and Qian, K.W., “Grain Refinement an Crack Preventation in Constrained Groove Pressing of Two Phase Cu-Zn Alloys”, Scripta Materialia, Vol. 57, pp. 987-990, (2007).
 
[7]     Peng, K., Zhanga, Y. L., Shaw, L., and Qian, K.W., “Microstructure Dependence of a Cu–38Zn Alloy on Processing Conditions of Constrained Groove Pressing”, Acta Materialia, Vol. 57, pp. 5543–5553, (2009).
 
[8]     Yoon, S.C., Krishnaiah, A., Chakkingal, U., and Kim, H.S., “Severe Plastic Deformation and Strain Localization in Groove Pressing”, Computational Materials Science, Vol. 43, pp. 641-645, (2008).
 
[9]     Shirdel, A., Khajeh, A., and Moshksar, M.M., “Experimental and Finite Element Investigation of Semi-constrained Groove Ressing Process”, Materials and Design, Vol. 31, pp. 946-950, (2010).
 
[10] Khodabakhshi, F., Kazeminezhad, M., and Kokabi, A.H., “Constrained Groove Pressing of Low Carbon Steel: Nano-structure and Mechanical Properties”, Materials Science and Engineering A, Vol. 527, pp. 4043–4049, (2010).
 
[11] Xiaolei, Dong, B. Y., and Zhihao, M., “Grain Refinement in Constrained Groove Pressing of 7050 Aluminum Alloy”, Advanced Materials Research, Vol. 189-193, pp. 2823-2826, (2011).
 
[12] Mou, X., Peng, K., Zeng, J., Shaw, L., and Qian, K.W., “The Influence of the Equivalent Strain on the Microstructure and Hardness of H62 Brass Subjected to Multi-cycle Constrained Groove Pressing”, Journal of Materials Processing Technology, Vol. 211, pp. 590–596, (2011).
 
[13] Borhani, M., and Djavanroodi, F., “Rubber Pad-constrained Groove Pressing Process: Experimental and Finite Element Investigation”, Materials Science and Engineering A, Vol. 546, pp. 1–7, (2012).
 
[14] Khakbaz, F., and Kazeminezhad, M., “Work Hardening and Mechanical Properties of Severely Deformed AA3003 by Constrained Groove Pressing”, Journal of Manufacturing Processes, Vol. 14, pp. 20–25, (2012).
 
[15] Khakbaz, F., and Kazeminezhad, M., “Strain Rate Sensitivity and Fracture Behavior of Severely Deformed Al–Mn Alloy Sheets”, Materials Science and Engineering A, Vol. 532, pp. 26– 30, (2012).
 
[16] Ratna Sunil, B., Arun Anil Kumar, Sampath Kumar, T.S., and Uday Chakkingal, “Role of Biomineralization on the Degradation of Fine Grained AZ31 Magnesium Alloy Processed by Groove Pressing”, Materials Science and Engineering C, Vol. 33, pp. 1607–1615, (2013).
 
[17] Khodabakhshi, F., Abbaszadeh, M., Eskandari, H., and Mohebpour, S.R., “Application of CGP-cross Route Process for Microstructure Refinementand Mechanical Properties Improvement in Steel Sheets”, Journal of Manufacturing Processes, Vol. 15, No. 4, pp. 533-541, (2013).
 
[18] Ebrahimi, M., Attarilar, Sh., Djavanroodi, F., Gode, C., and Kim, H.S., “Wear Properties of Brass Samples Subjected to Constrained Groove Pressing Process”, Materials and Design, Vol. 63, pp. 531–537, (2014).
 
[19] Zongshen, W., Yanjin, G., and Chongkai, Z., “Effects of Friction on Constrained Groove Pressing of Pure Al Sheets”, Advanced Materials Research Vol. 926-930, pp. 81-84, (2014).
 
[20] Zong-Shen, W., Yan-Jin, G., Guang-Chun, W., and Chong-Kai, Z., “Influences of Die Structure on Constrained Groove Pressing of Commercially Pure Ni Sheets”, Journal of Materials Processing Technology, Vol. 215, pp. 205–218, (2015).
 
[21] Kazeminezhad, M., and Hosseini, E., “Optimum Groove Pressing Die Design to Achieve Desirable Severely Plastic Deformed Sheets”, Materials and Design, Vol. 31, pp. 94–103, (2010).
 
[22] Hosseini, E., Kazeminezhad, M., Mani, A., and Rafizadeh, E., “On the Evolution of Flow Stress during Constrained Groove Pressing of Pure Copper Sheet”, Computational Materials Science, Vol. 45, pp. 855–859, (2009).
 
[23] Zhu, Y.T., Lowe, T.C., and Langdon, T.G., “Performance and Applications of Nanostructured Materials Produced by Severe Plastic Deformation”, Scripta Materialia, Vol. 51, pp. 825-830, (2004).
 
[24] Luo-xing, L.I., Guan Wang, Jie, L.I.U., and Zai-qi, Y., “Flow Softening Behavior and Microstructure Evolution of Al−5Zn−2Mg Aluminum Alloy during Dynamic Recovery”, Transactions of Nonferrous Metals Society of China, Vol. 24, pp. 42−48, (2014).
 
Khodabakhshi, F., and Kazeminezhad, M., “The Effect of Constrained Groove Pressing on Grain Size, Dislocation Density and Electrical Resistivity of Low Carbon Steel”, Materials and Design, Vol. 32, pp. 3280–3286, (2011).