[1] Powell, N., and Andrew, C., "Incremental Forming of Flanged Sheet Metal Components without Dedicateddies", IMECHE Part , J. Engineering Manufacture, Vol. 206, pp. 41- 47, (1992).
[2] Sedighi, M., and Honarpisheh, M., "Investigation of Cold Rolling Influence on Near Surface Residual Stress Distribution in Explosive Welded Multilayer", Strength of Materials, Vol. 44, No. 6, pp. 693-698, (2012).
[3] Akbari Mousavi, S.A.A., and Farhadi Sartangi, P., "Effect of Post-weld Heat Treatment on the Interface Microstructure of Explosively Welded Titanium–Stainless Steel Composite", Materials Science and Engineering A, Vol. 494, pp. 329–336, (2008).
[4] Hussain, G., Gao, L., and Zhang, Z. Y., "Formability Evaluation of a Pure Titanium Sheet in the Cold Incremental Forming Process", Int J Adv Manuf Technol, Vol. 37, pp. 920–926, (2008).
[5] Mirnia, M. J., and Dariani, B. M., "Analysis of Incremental Sheet Metal Forming using the Upper-bound Approach", Proceedings of the Institution of Mechanical Engineers, Part B, Journal of Engineering Manufacture, Vol. 226, No. 8, pp. 1309-1320, (2012).
[6] Liu, Z.B., Li, Y.L., Daniel, W.J.T.B., and Meehan, P., "Taguchi Optimization of Process Parameters for Forming Time in Incremental Sheet Forming Process", Materials Science Forum, Vols. 773-774, No. 137143, pp. 773-774, (2014).
[7] Hamilton, K., and Jeswiet, J., "Single Point Incremental Forming at High FeedRates and Rotational Speed: Surface and Structural Consequences", CIRP Annals ManufacturingTechnology, Vol. 59, pp. 311‐314, (2010).
[8] Ghasemi, H., and Solttani, B., "Experimental Investigation on the EffectiveParameters on Forming Force, Dimensional Accuracy and Thickness Distribution in Single Point Incremental Forming", Modares Mechanical Engineerring, Vol. 14, No. 1, pp. 89-96, (2014). (In Persian).
[9] Shanmuganatan, S. P., and Kumar, V. S., "Modeling of Incremental Forming Process Parameters of Al 3003 (O) by Response Surface Methodology", Procedia Engineering, Vol. 97, pp. 346– 356, (2014).
[10] Honarpisheh, M., Abdolhoseini, M. J., and Amini, S., "Experimental and Numerical Investigation of the Hot Incremental Forming of Ti-6Al-4V Sheet using Electrical Current", The International Journal of Advanced Manufacturing Technology, Vol. 83, No. 9, pp. 2027-2037, (2016).
[11] Gheysarian, A. and Honarpisheh, M., "Process Parameters Optimization of the Explosive-Welded Al/Cu Bimetal in the Incremental Sheet Metal Forming Process", Iranian Journal of Science and Technology, Transactions of Mechanical Engineering, doi.org/10.1007/s40997-018-0205-6, (2018).
[12] Gheysarian, A. and Honarpisheh, M., "An Experimental Study on the process parameters of Incremental Forming of Explosively-Welded Al/Cu Bimetal", Journal of Computational & Applied Research in Mechanical Engineering (JCARME), Vol. 7, No. 1, pp. 73-83, (2017).
[13] Honarpisheh, M., Niksokhan, J., and Nazari, F., "Investigation of the Effects of Cold Rolling on the Mechanical Properties of Explosively-welded Al/St/Al Multilayer Sheet", Metallurgical Research & Technology, Vol. 113, No. 1, pp. 105, (2016).
[14] Asemabadi, M., Sedighi, M., and Honarpisheh, M., "Investigation of Cold Rolling Influence on the Mechanical Properties of Explosive-welded Al/Cu Bimetal", Materials Science and Engineering A, Vol. 558, pp. 144-149, (2012).
[15] Myers, H. R., and Montgomery, D. C., "Response Surface Methodology", John Wiley & SONS, INC, (2002).
[16] Ambrogio, G., Filice, L., and Micari, F., "A Force Measuring Based Strategy for Failure Prevention in Incremental Forming", Journal of Materials Processing Technology", Vol. 177, pp. 413-416, (2006).